Release Notes for AirGap for Dell
This page lists the changes, fixes, and known issues for AirGap for Dell version 2.15.1.
What's Fixed in Version 2.15.1
-
License Management Cards Show the Correct Capacity: Fixed a capacity display issue on the License Management cards, where some licenses, such as Disaster Recovery, showed a capacity of 0 / 0 TB.
-
Disk Usage Is Now Shown for ECS Devices in Inventory: On Inventory → Manage Devices, ECS devices previously showed an empty disk usage slot. Disk usage is now reported for ECS devices. Consumed space is calculated as total minus free, so space reserved by ECS counts as consumed and the figure can read higher than the "% Full" shown in the ECS console. Devices that have not yet reported inventory show an "awaiting inventory" state instead of an empty value.
-
ECA Firewall Now Blocks Unauthorized Network Traffic by Default: The ECA host firewall's final drop rule only applied to an interface named
eth0, so on appliances whose network interface uses a different name (such asens160), traffic from hosts outside the allowed list was not blocked and internal cluster services could be reached from arbitrary network hosts. The firewall now denies all traffic that is not explicitly allowed, regardless of the interface name. SSH and HTTPS access are unchanged. -
Restoring a Pre-2.15 Backup Onto a 2.15 Appliance No Longer Stops
sca.service: Restoring a backup taken on a release earlier than 2.15 onto a 2.15 appliance could leavesca.serviceunable to start, with a keystore password verification error, because the restored keystore password was not carried over to the new 2.15 password location. The restore now reconciles the password, and the service starts normally after the restore. -
Zookeeper Now Starts With the Configured Log Level: After a restart or cluster up, Zookeeper could start in debug mode instead of using the configured log level, which could contribute to memory issues on the ECA. Zookeeper now starts with the intended log level.
-
/opt/dataNo Longer Fills Up With Zookeeper and Turbo Audit Logs: Fixed an issue where the Zookeeper and turboaudit log directories under/opt/data/superna/logskept growing until/opt/datareached 100% utilization, which left ECA nodes inactive. -
Zookeeper Backup and Restore Problem Fixed: Fixed a problem with the Zookeeper backup and restore process.
Known Issues
The following known issues have been identified in version 2.15.1.
-
AirGap Runs and Job History Tabs Do Not Record Scheduled ECS AirGap Sync Runs: The AirGap Runs tab in the new UI and the Job History tab in the Old (legacy) GUI stop recording scheduled ECS AirGap sync runs for any job, regardless of how it was scheduled. The Config and Reports tabs continue to show every run correctly.
A schedule that you set or change while the Eyeglass service is running is not applied by Eyeglass until the service restarts, so the runs that follow it are not recorded in the Runs and Job History tabs. The copy to the vault still runs at the new time.
Workaround: Restart the Eyeglass service after you set or change an AirGap schedule. To confirm that a scheduled copy ran, check Last Run on the AirGap Config tab or the Reports tab.
-
Create New Report Does Not Respond in the Old GUI for PowerScale AirGap: On AirGap for PowerScale, the Create New Report button does not respond in the Old (legacy) GUI. In the New GUI, the button opens a window where you select the date range.
Workaround: Create the report in the New GUI.
Previous Release - 2.15.0
Known Issues
The following known issues have been identified in version 2.15.0.
-
Signing Into One UI Signs You Out of the Other: Signing in to the Old (legacy) GUI while already signed in to the New GUI — or vice versa — signs you out of the other interface after a few seconds. Signing in to the New GUI first does not cause this and then signing in to the Old GUI.
-
Cannot Schedule an AirGap Job to Run More Than Once Per Hour or Day: The new UI does not currently support scheduling an AirGap job to run multiple times within an hour or a day. The Old (legacy) GUI supports this option when configuring a policy schedule.
See Also
- What's New – Current landing page for release information.
- Prerequisites – Current platform compatibility tables.
- Installation Guide – Install and deploy AirGap.
Need Help?
- Contact Support: Reach out to Superna Support for configuration assistance or troubleshooting help.