Post-Deployment Environment Setup

Introduction

With DR Deployed, the environment must be set up in the software. Topics like registering a license, and adding clusters are all covered inside this guide.

Register Superna License

Retrieve the Superna Disaster Recovery Edition license keys from the Zendesk case by following these steps:

1. Login to the Superna Support Desk.

   note

   Ensure a valid support account is logged in to access the license key download dialog box.

   Submit the license request by entering the Appliance ID and Transaction Token as provided in the license email.

   note

   The Appliance ID and Transaction Token must be entered exactly as shown on the license email, with all dashes and without any leading or trailing spaces.

   Ex. EMC-xxx-xxx-xxx-xxx

2. Download the provided zipped license file.

   warning

   Do not unzip the license file; the .zip file will be uploaded in the next step.

3. Upload License File Click License Management > Manage Licenses > Browse

   Upload the zipped file downloaded in the previous step.

   note

   After clicking Upload, the Eyeglass EULA must be accepted to continue the process.

Add Clusters

warning

Ensure that both the source and target clusters comply with the support feature matrix. Additionally, all PowerScale cluster replication pairs should operate on a OneFS version that is listed and supported as per the System Requirements / Feature Release Compatibility matrix.

1. Open the Eyeglass UI to get started.

2. In the Eyeglass Main Menu, select Add Managed Device to start adding cluster configurations.

3. Provide the cluster details as prompted by the interface.

   PowerScale

   • Node IP in System Zone (not SSIP): Provide an IP address allocated for the System Access Zone. Avoid using SSIP, as it is unsuitable for administrative connections.

     note

     Starting from release 2.5.5, it is mandatory to use a node IP with dynamic IP allocation within a subnet that is part of the System Access Zone. This requirement is due to a CSRF security patch that disables basic authentication and prevents session tokens from being shared between PowerScale nodes. For further details, refer to the associated technical documentation.

   • Port: Default to 8080 unless there is a requirement for a different port number.

   • Username and Password: Input the username and password of the Eyeglass service account.

   • Maximum RPO Value: (Optional) Define the recovery point objective in minutes, if desired.

   • Active Directory Username and Password for Runbook: (Optional) Enter if you're using AD credentials for Runbook automation.

4. Submit the form to add the cluster to Eyeglass.

Verify Inventory Collection

After adding a cluster, Superna DR Edition initiates an automatic inventory task to identify and catalog the cluster's components.

note

The inventory discovery process typically takes between 5 to 10 minutes.

Once this inventory task completes, the results are displayed in the Inventory View.

To access this, click the Inventory View icon.

This will open the Inventory View window, showing a list of all managed devices.

note

The Inventory View does not auto-refresh. To view the most up-to-date information, manually refresh the page by clicking the Refresh button located at the bottom right corner of the GUI.

Remember: The inventory discovery process typically takes between 5 to 10 minutes.

Monitor this process and verify that all components have been correctly added and displayed.

Enable/Disable Jobs

This section will walk you through the process of enabling or disabling jobs, including bulk actions for managing multiple jobs at once.

1. Open the Eyeglass Main Menu

   From the main dashboard, locate and click the Jobs icon, which is located in the top-middle section of the screen and represented by a checklist icon.

2. View the Jobs List

   Once the Jobs window is open, you'll see a list of available jobs. You can view details such as the job name, policy, type, last run date, and the current state.

3. Select Jobs to Enable or Disable

   Check the box next to the jobs you want to enable or disable.

   info

   You can select more than one job at the same time by checking multiple boxes.

4. Use the Bulk Action to Enable or Disable Jobs
   After selecting the jobs, look at the bottom right of the window for the dropdown button labeled Select a bulk action. Click on this button and choose either Enable or Disable based on the action you want to perform.

5. Effect of Enabling the Job

   info

   On the next Configuration Replication cycle, the enabled Job will be run.

   This process allows you to manage multiple jobs efficiently by enabling or disabling them in bulk.

Setup Notifications

Configure SMTP

Enter the information for an email server by clicking Notification Center > Configure SMTP in the Eyeglass Main Menu:

To continue the configuration of SMTP:

• In the Host name: textbox enter the host name for the email server.

• In the Port textbox, type the port which should be used for sending email.

• In the From: textbox, enter the email address of the sender of the email. Any String before and after @ is accepted:

  Syntax: xx@y, xx@y.z E.g.: alerts@eyeglass, alerts@eyeglass.com, etc.

• Tick the Use Authentication: checkbox if email server requires an authenticated login.

• In the User: textbox, provide the user or email address required for authentication.

• In the Password: textbox, provide the password for authentication.

• Tick Enable TLS: checkbox if the email server expects TLS communication.

• Alarm Severity Filter: Select level of alarms to receive emails for. Note that alarms more severe than the selected filter are also emailed.

  • Use the Test Email Setting button to check that the email server information added is correct. If an error occurs, there are error codes from the SMTP connection. The "no error" response indicates a successful connection. If an error is returned the debug response should be sent to https://support.superna.net.

Save the changes.

Configure Email Recipients

Enter the information for email recipients by clicking Eyeglass Main Menu > Notification Center > Manage Recipients.

• Enter the email address in the Email Recipient: textbox.

• Select the report type for this user to receive. The following options are available:

  • All (All Reports & Alerts)

  • Reports (RPO, cluster configuration)

  • Auditor Only Reports (All reports and email notifications for Easy Auditor)

  • Quota Management (Quota Usage reports for Cluster Storage Monitor solution)

  • Data recovery+ (Cluster Storage Monitor product Data Recovery portal emails)

  • Click the Add/Edit button.

Optional Steps

Next Steps

That completes the installation process. A good place to consult next can be: Eyeglass Jobs